DMS International
![]()
REPLACEMENT MICRO SWITCH SET FOR SG-2100 DiSEqC MOTOR
MICRO SWITCH SET FOR SG-2100 and other DiSEqC MOTOR
This is the micro switch set used in the SG-2100 DiSEqC motor.
Micro switches often fail. Use this replacement switch set that comes directly from the SG-2100 factory.
Comes with both switches on one PCB and the pigtail with connector as shown in the pictures.
If you have a genuine SG-2100 this is a direct replacement. This switch set was used in most brands of DiSEqC motors.
Check the pictures carefully and compare to your parts before purchasing.
FTA, SKY MEXICO, DBS Satellite Ku Universal Mono-block LNBF for 4° spacing
Brand: DMS International
Model: JSC-MB4-2
Why are these so cheap? We are closing these out at a super low price. They are new. We have not had any problems with this LNBF.
Digital Ready, HDTV approved, latest technology provides the best possible performance.
Receives two satellites at four degree spacing.
Commonly used for Galaxy 19 (97.0°W) and SES 1 (101.0°W)
This is a 'Universal' LNBF that works anywhere in the world.
Works for SKY MEXICO, FTA, DBS, and more.
The famous DMS DiSEqC switch is built in allowing you to deliver both signals down one coax without adding more devices in line. 0.2dB noise figure, high stability and high gain insures that you get the best possible picture. Only JSC LNBFs have the ability to give you the best reception.
| Specifications | |
| Input Frequency | 10.7 - 11.7 GHz and 11.7 - 12.75 GHz |
| Output Frequency | 950 - 1950 MHz and 1100 - 2150 MHz |
| LO Frequency | 9.75 GHz and 10.6 GHz |
| LO Initial Accuracy (@25°C) | ± 1 MHz |
| LO Temperature Drift (@ -40 to 60°C) | ± 3 MHz |
| LO Phase Noise (@ 1 KHz offset) | -60 dBc/Hz |
| LO Phase Noise (@ 10 KHz offset) | -80 dBc/Hz |
| LO Phase Noise (@ 100 KHz offset) | -100 dBc/Hz |
| Noise Figure | 0.2 dB |
| Conversion Gain | 50 to 62 dB |
| Gain Variation (over operating band) | 5 dB p-p (typical) |
| Gain Flatness (any 27 MHz) | ± 0.5 dB |
| Cross Pol. Isolation | 20 dB (minimum) 25 dB (typical) |
| Image Rejection | 40 dB (minimum) |
| P 1 dB | 0 dBm (minimum) |
| Output VSWR | 2:1 |
| Spurious Response (@ 1700 MHz) | -58 dBm (maximum) |
| DC Current Consumption | 180 mA (maximum) |
| Polarization Switching Voltage | Vertical: 10.5 to 14.2 volts Horizontal: 15.5 to 21 volts |
| Band Switching | Low: 0 KHz, High 22 ± 4 KHz |
| LO Spurious | -45 dBm (maximum) |
| Operation Temperature | -40°C to 60°C |
| Waterproof | +60°C water for 5 minutes |
| Output Connector | 75 ohm F type |
Universal Ku LNBF Model KSC321S-2 0.2 dB Noise Figure by DMSIUSA
High gain, quality Ku Universal LNBF
High gain single output Ku LNBF using 10.7 to 12.75 GHz Universal with 09750 and 10600 MHz LO frequencies. Rock solid stability and 0.2 dB noise figure. 40mm throat size allows mounting to all popular dishes. Works world wide!
Specs:
- Input: 10.70 ~ 12.75GHz
- Output: 950 ~ 2150MHz
- L.O.: 9.75/10.60GHz
- Noise: 0.2dB
- Gain: 60dB
Don't be fooled by the price.
This is the best LNBF featuring very high gain while maintaining great stability.
We have never had a failure of this LNBF.
KSC322-2 Twin Universal Ku LNBF 0.2dB Noise Figure by DMSIUSA
High gain, high quality Twin Universal Ku LNBF
High gain twin output Ku LNBF using 10.7 to 12.75 GHz Universal with 09750 and 10600 MHz LO frequencies. Rock solid stability and 0.2 dB noise figure.
Twin outputs means you can operate 2 receivers from this LNBF and have full control over both receivers at the same time. You cannot use a splitter to feed two receivers from a single output LNBF. If you are adding that second receiver, this is the LNBF you need. 40mm throat allow mounting it on the most popular dishes. 0.2dB noise and excellent stability means you will have great pictures receiving digital or analog.
Specs:
- Input: 10.70 ~ 12.75GHz
- Output: 950 ~ 2150MHz
- L.O.: 9.75/10.60GHz
- Noise: 0.2dB
- Gain: 60dB
Don't be fooled by the price.
This is the best LNBF featuring very high gain while maintaining great stability.
We have never had a failure of this LNBF.
Di-electric plate used on BSC621, BSC621-2 and BSC622
Converts your C or C/Ku band Linear LNBF to a Circular LNBF
Originally came in the BSC621, BSC621-2 and BSC622 but works for most LNBFs.
This dielectric plate will fit inside most standard size 65mm OD C or C/Ku band LNBF.
Can be filed or sanded down for a perfect fit in other LNBFs.
| Details | |
|---|---|
| Manufacture | DMS International |
| Model | Di-electric plate for BSC621 & BSC621-2 |
| Condition | New |
Dielectric plates are used to convert circularly polarised signals to linear polarisation. They work by utilising the difference in dielectric constant between fibreglass and air.
Signals entering a waveguide parallel to the plate will undergo a phase shift different to the signal entering the waveguide at 90 degrees to the plate, allowing Circular polarisation.
KSC322-2 Twin Universal Ku LNBF 0.2dB Noise Figure by DMSIUSA
High gain, high quality Twin Universal Ku LNBF
New, unused, but with no box. Only 1 piece at this cost.
High gain twin output Ku LNBF using 10.7 to 12.75 GHz Universal with 09750 and 10600 MHz LO frequencies. Rock solid stability and 0.2 dB noise figure.
Twin outputs means you can operate 2 receivers from this LNBF and have full control over both receivers at the same time. You cannot use a splitter to feed two receivers from a single output LNBF. If you are adding that second receiver, this is the LNBF you need. 40mm throat allow mounting it on the most popular dishes. 0.2dB noise and excellent stability means you will have great pictures receiving digital or analog.
Specs:
- Input: 10.70 ~ 12.75GHz
- Output: 950 ~ 2150MHz
- L.O.: 9.75/10.60GHz
- Noise: 0.2dB
- Gain: 60dB
Don't be fooled by the price.
This is the best LNBF featuring very high gain while maintaining great stability.
We have never had a failure of this LNBF.
FTA, SKY MEXICO, DBS Satellite Ku Universal Mono-block LNBF for 4° spacing
FREE, just pay shippng.
Brand: DMS International
Model: JSC-MB4-2
Why are these so cheap? We are closing these out at a super low price. They are new. We have not had any problems with this LNBF.
Digital Ready, HDTV approved, latest technology provides the best possible performance.
Receives two satellites at four degree spacing.
Commonly used for Galaxy 19 (97.0°W) and SES 1 (101.0°W)
This is a 'Universal' LNBF that works anywhere in the world.
Works for SKY MEXICO, FTA, DBS, and more.
The famous DMS DiSEqC switch is built in allowing you to deliver both signals down one coax without adding more devices in line. 0.2dB noise figure, high stability and high gain insures that you get the best possible picture. Only JSC LNBFs have the ability to give you the best reception.
| Specifications | |
|---|---|
| Input Frequency | 10.7 - 11.7 GHz and 11.7 - 12.75 GHz |
| Output Frequency | 950 - 1950 MHz and 1100 - 2150 MHz |
| LO Frequency | 9.75 GHz and 10.6 GHz |
| LO Initial Accuracy (@25°C) | ± 1 MHz |
| LO Temperature Drift (@ -40 to 60°C) | ± 3 MHz |
| LO Phase Noise (@ 1 KHz offset) | -60 dBc/Hz |
| LO Phase Noise (@ 10 KHz offset) | -80 dBc/Hz |
| LO Phase Noise (@ 100 KHz offset) | -100 dBc/Hz |
| Noise Figure | 0.2 dB |
| Conversion Gain | 50 to 62 dB |
| Gain Variation (over operating band) | 5 dB p-p (typical) |
| Gain Flatness (any 27 MHz) | ± 0.5 dB |
| Cross Pol. Isolation | 20 dB (minimum) 25 dB (typical) |
| Image Rejection | 40 dB (minimum) |
| P 1 dB | 0 dBm (minimum) |
| Output VSWR | 2:1 |
| Spurious Response (@ 1700 MHz) | -58 dBm (maximum) |
| DC Current Consumption | 180 mA (maximum) |
| Polarization Switching Voltage | Vertical: 10.5 to 14.2 volts Horizontal: 15.5 to 21 volts |
| Band Switching | Low: 0 KHz, High 22 ± 4 KHz |
| LO Spurious | -45 dBm (maximum) |
| Operation Temperature | -40°C to 60°C |
| Waterproof | +60°C water for 5 minutes |
| Output Connector | 75 ohm F type |
6 foot RS-232 Female to Female Null Modem Cable
High Quality DB9 (9 pin) connectors on High Quality 6 footCable
Packed 1 piece per shipment.
Total is 1 piece.
null modem cable:
Sometimes called a twisted pair cable. The ends are RS232 9 pin. Although it is a 9 pin cable the only connections required are:
- pin 2 to pin 3
- pin 3 to pin 2
- pin 5 to pin 5
- 1